::|CONTENTS
- Normal Effects
- Channel-Specific Effects
- Table Effects
- See Also
Normal Effects
Axx - Run table
xx = Table index
Valid range = 00 - 1F
Cxy - Arpeggio aka
arps; fast note shifting in half steps.
x = Number of half steps from root note for first shift
y = Number of half steps from root note for second shift
Ex: 037 = Minor chord. 047 = Major chord. 070 = Perfect 5th
View article on
arps for more examples.
Notes: Leaving y blank causes the arp to last two ticks instead of three.
Dxx - Delay row
xx = Amount of ticks before row is played
Gxx - Set groove (tempo pattern)
xx = Groove index
Valid range = 00 - 1F
Notes: Each channel and each table uses an independent groove.
Hxx - Skip to next phrase
If xx = 00-0F: Row index (in hexadecimal)
If xx = FF: Halt song
Kxx - Delayed note cut.
xx = Ticks before note is cut.
Notes: K00 is effectively the same as a note cut event.
Lxx - Slide from previous note
xx = speed
Note: becomes about six times as fast when the current instrument's VIB.TYPE is set to HF sine.
Mxy - Master volume
x = Left output volume
y = Right output volume
Valid range for x and y = 0 - 7
OLR - Left/right output
If L or R is on: Left/right output of the channel is enabled
If L or R is off: Left/right output of the channel is disabled
Pxx - Pitch bend
If xx = 00: Default
If xx = 01-7F: Increase pitch
If xx = 80-FF: Decrease pitch
Note: becomes about six times as fast when the current instrument's VIB.TYPE is set to HF sine.
Rxy - Retrigger note
If x = 0: Constant volume
If x = 1-7: Increase volume on each note
If x = 8-F: Decrease volume on each note
y = Ticks to wait between successive notes
Note: Ignores x on the wave channel.
Txx - Set tempo
xx = Tempo value in BPM
Notes: The minimal tempo is 0x50 = 80.
Vxy - Vibrato; pitch vibration.
x = Speed
y = Depth
Note: becomes about six times as fast when the current instrument's VIB.TYPE is set to HF sine.
Zxx - Randomize command
Recalls the latest command by adding a random number between 0x00 and xx to the effect value.
Channel-Specific Effects
Exy - Hardware volume envelope
x = Initial volume
If y = 0 or 8: Sustain
If y = 1-7: Decay, 1 being the fastest
If y = 9-F: Attack, 9 being the fastest
Applies to: Pulse 1 / 2, Noise
Exx - Wave volume setting
xx = Volume
Valid range = 00 - 03
Applies to: Wave
Fxx - Wave kit sample offset / Wave index offset.
The command argument is added to the current wave index.
xx = Sample offset (must be positive) or wave index offset
Applies to: Wave
Sxy - Hardware sweep
x = Speed
If y = 1-7: Shift downward, 7 is deepest
If y = 9-F: Shift upward, F is deepest
Valid range for x = 1 - 7
Applies to: Pulse 1
Sxx - Wave index setting
xx = Waveform index
Applies to: Wave
Wxx - Set duty
This effect is edited graphically under normal conditions, but sometimes the display might glitch temporarily causing numbers to be shown.
xx = Square duty cycle
-_______ = 00 = 12.5% Duty
--______ = 01 = 25% Duty
----____ = 02 = 50% Duty
------__ = 03 = 75% Duty
Applies to: Pulse 1 / 2
Table Effects
Hxy - Table repeat settings.
If xy = FF: Halt table
Otherwise,
If x = 0: Loop indefinitely
If x = 1-F: Jump to row y for x times
See Also
LSDJ
